Instead, you should troubleshoot the float switch and find out why it’s not functioning.Ī few of the most common reasons a float switch will stop working include: Therefore, the pump will burn out faster than it should if left connected to direct power. The continuous power supply causes the pump’s motor to run nonstop. While bypassing the float switch temporarily is fine so you can eliminate waste in the holding vessel, this is not a long-term solution. Sometimes, the float switch will quit working, so homeowners will take the obvious route of bypassing the float switch by supplying the pump with direct power. Sewage ejector pumps have a float switch much like a sump pump, which means when fluid levels reach a point where the float of the unit rises to a certain level, the pump will automatically activate. Bypassing the Float Switch for Long Periods with Direct Power Here is a look at two of the most common reasons for premature sewage ejector pump failure. While most sewage ejector pumps are designed to withstand at least 7 to 10 years of use, with some even lasting much longer, occasionally problems do arise long before the pump has reached the end of its life span. If you have a sewage ejector pump, you should get familiar with general maintenance needs and signs that the pump is not working properly. In the modern, multi-level home, sewer ejector pumps make it possible to move the solid waste from drainage points through the septic lines and to the disposal area, whether it is a private septic tank or public sewer system. WHY DID YOUR HOME SEWER EJECTOR PUMP FAIL If you’ve been experiencing any of these issues with your pump, contact the friendly experts at Simonds Machinery Company to get the problem taken care of as quickly as possible. Ignoring the problem is only going to make it worse and could lead to lasting damage. It’s up to you, however, to notice the warning signs and to act fast if you do happen to notice one of these issues. However, any sounds that you don’t recognize or are not accustomed to should be cause for concern and action.Īs you can see, your industrial pump will typically let you know when there is some kind of issue. You should especially be mindful of clanging or banging noises, which typically indicate either a problem with the overall mechanics of the pump or with its structure and integrity. Sign #4: Your Pump Is Making Strange Soundsįinally, as is the case with any type of machinery, especially one as all-important as a pump, if your pump suddenly starts making odd noises, it is definitely time to get it looked at. As is the case with all of these problems, the best way to diagnose and properly fix the issue is with professional assistance and advice. The issue could be a poorly or improperly adjusted switch, a burnt-out motor, or issues communicating commands to turn on or off. If, however, you find that your pump constantly seems to be cycling, so much so that you can never really determine what stage it is at or if it is doing its job properly, then you definitely have a problem of some sort on your hands. Just about every type of industrial pump that you could ever purchase will cycle on and off that is just how the vast majority of pumps work. Instead of putting yourself or your workers at risk to try and figure out the problem, have professionals take a closer look. It could also be the case that your pump has simply “given out.” It could be the result of anything from electrical problems to frayed wires to a blown fuse. There are a variety of reasons that this issue could pop up. It is also an issue if it struggles or is slow to start. Obviously, when your day-to-day operations rely on a working pump, it is a major problem if your pump won’t start. Sign #2: Your Pump Won’t Start Or Struggles To Start Your best bet for determining what is causing the problem is to have a professional inspect your pump for you. Furthermore, it also indicates that something isn’t quite right with your pump. When that isn’t happening and you’re getting dirty, murky water instead, it can take a serious toll on your business operations. The whole purpose of having a pump, no matter the exact type, is to regularly filter clean, clear water into your operations. To start off with, one of the first things to be on the lookout for is dirty water running through your systems. That way, you will all be aware when something is wrong, and you will be able to seek pump repair or replacement early on before there is a chance for any more severe damage to take place. The key is to educate yourself and your workers on the warning signs of an impending pump failure. With continual use, almost every pump will fail or at least run into issues at some point. With that said, no industrial pump, no matter how well-made it is, is designed to last forever. Industrial pumps come in all types and designs.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |